AP Techno Oil & Gas Instrumentation

Helium Porosity Meter

Helium Porosity measuring instrument with capability determine Pore Diameter , Total Pore Volume , Surface Area & Total / Bulk densities , in addition to Porosity of Core sample

  • Accuracy 0.995 gms/cc Porosity .
  • Core Sample size – Dia 1.5 inch & Length up to 4 inch
  • Incorporates 1.5 inch Matrix Cup and Grain Volume Billet – 1 each
  • Accuracy of Temp compensated Pressure Transducer – 0.05 % FS
  • Microcontroller based Pressure sensing and data processing
  • Compact design with User friendly Dedicated Software
  • Manual Valve Operation and Digital Display ( with option to run with or without PC )
  • System Interface – USB / RS232
  • 230 V , 50 Hz , Single Phase , -- KVA

Steady State Gas Permeameter

For accurate determination of  Permeability to gas of plug size core samples at ambient temperature and moderate confining pressure by steady state method, by applying a constant flow rate across the sample. Gas can be injected over a wide range of pressure and flow rates.

The core inlet pressure is continuously monitored by an inline differential pressure measurement, while gas flow rate is monitor & recorded by a high -grade mass flow meter. Precession metering valve for back pressure control, allow  better Kinkenberg Interpretation.

Instrument can be used for both Consolidated or unconsolidated samples. Dedicated software and data handling provide live calibration and measurement.

Electrical Property measurement system

System design to measure various electrical properties of core plug samples, such as determination of formation factor, Resistivity Index, saturation exponent “n” & Cementation factor “m” along with Capillary pressure vs water saturation (Drainage and imbibition).

This system having capability to measure resistivity for both full & partially brine saturated core sample as well as brine electrical resistivity at ambient conditions.

Liquid Permeameter

This system can be used for both Steady and Unsteady state measurement.

For accurate determination of  Permeability to liquid of plug size core samples at ambient temperature and moderate confining pressure by steady state method, by applying a constant flow rate across the sample. Liquid can be injected over a wide range of pressure and flow rates.

The core inlet pressure is continuously monitored by an inline differential pressure measurement, while liquid flow rate is monitor & recorded by a high -grade mass flow meter. Precession metering valve for back pressure control, allow  better Interpretation.

Instrument can be used for both Consolidated or unconsolidated samples. Dedicated software and data handling provide live calibration and measurement.

core gama

Core gamma Spectro System

Spectral logging is the technique of measuring the spectrum, or number and energy, of gamma rays emitted via natural radioactivity of the rock formation.

There are three main sources of natural radioactivity on Earth: potassium (40K), thorium (principally 232Th and 230Th), and uranium (principally 238U and 235U).

The quantity and energy of these gamma rays can be measured by a scintillation Counter.

A log of the spectroscopic response to natural gamma ray radiation is usually presented as a total gamma ray log that plots the weight fraction of potassium (%), thorium (ppm) and uranium (ppm).

core flow system

Core Flow System

A core flooding system is a system that flows a fluid (gas or liquid) through a core sample at controlled conditions and measures flow parameters.  

Because of the wide variety of tests that might be conducted in a core flooding system, systems are typically customized to meet the exact requirements for a specific application. To provide the desired temperature an oven is used to allow core flooding tests to be conducted at fixed temperature from room temperature up to 150 °C.

The inside chamber is made stainless steel 304 and it is rectangular in shape (with full toughen glass window to view in.

Multiphase core-flow system / acid flow system

core cutting

Core Cutting / Slabbing / Plugging machines

CS-01R/2020 model has unique design . Used to cute the core as well as slabbing of core. Specification of CS-01R/2020 Floor Mounted Core saw machine Diamond tooled with end face grinder Adjustable table Maximum Core Cutting Size : 450 mm Max core length: 300 mm.

CPM-01R/2019 unit used to drill plug sizes representative sample from given core sample. Specifications : Coring Dimater : 1.5″ Maximum coring depth : 5″

OEM

OEM – Microwave Assisted Gravity Drainage System

For Enhanced Oil Recovery Studies, this OEM product is designed to facilitate the study of microwave assisted gravity drainage.

laboratory

Laboratory EPC Services

  • Lab Consultancy
  • Lab Design & Engineering
  • Lab Instruments Supply- Manufacturing
  • Lab Consumable Supply
  • Consultancy Service for statutory Lab Audits
  • Experience Lab work Force Supply
  • Innovative IT support
  • Technical Service support & Lab Management
  • Design & Supply of Mobile Laboratory